ICP DAS

ICP DAS brings the most powerful, cost-effective, advanced Smart Power Meters PM-2133D series that gives you access to real-time electric usage for three-phase power measurement. With its high accuracy (<0.5%, PF=1), the PM-2133D series can be applied to both low voltage primary side and/or medium/high voltage secondary side and enables the users to obtain reliable and accurate energy consumption readings from the monitored equipment in real time under operation.

Features
• True RMS Power Measurements
• Energy Analysis for 3P4W, 3P3W, 1P3W, 1P2W
• Current Measurements Up to 400 A with Different CT Ratio
• Voltage Measurements Up to 500 V
• Clip-on CT for Easy Installation
• W Accuracy Better than 0.5% (PF=1)
• 8-Digit LED Display
• Supports Modbus RTU Protocol
• Total Harmonic Distortion (THD)
• Bi-directional Energy

When the inverter is running, it will generate some high frequency or low frequency noise, and interfere with the peripheral equipment by conduction or radiation. It is recommended that the CT and reference voltage of the meter be installed on the primary side of the “AC Filter” with an EMI ferrite core to minimize the interference effects of the inverter.

Features
• True RMS Power Measurements
• Energy Analysis for 3P4W, 3P3W, 1P3W, 1P2W
• Current Measurements Up to 400 A with Different CT Ratio
• Voltage Measurements Up to 600 V
• Clip-on CT for Easy Installation
• W Accuracy Better than 0.5% (PF=1)
• Multiple Data Format
• Supports Modbus RTU Protocol
• Total Harmonic Distortion (THD)
• Bi-directional Energy

ICP DAS brings the most powerful, cost-effective, advanced Smart Power Meters PM-3133-RCT that gives you access to real-time electric usage for three-phase power measurement.

Features
• Bi-directional Energy
• Energy Analysis for 3P4W, 3P3W, 1P3W, 1P2W
• Current Measurements Up to 500 ~ 4000 A
• Voltage Measurements Up to 500 V
• Rogowski Coil Soft CT for Easy Installation
• W Accuracy Better than 0.5% (PF=1)
• RS-485 or Ethernet (PoE) Communication
• Supports Modbus RTU Protocol
• Total Harmonic Distortion (THD)
• Builit-in 2 Power Relay Output (Form A)
• EC 61010-1 and EN 61010-1

Features
• Powerful MCU handles efficient network traffic
• Integrate RS-232/422/485 serial device to EtherCAT
• 2 x RJ-45 bus EtherCAT interface, support Daisy Chain
• Supports maximum 128 Input and Output Data
• Supports maximum 6 connection for PM-3033/3133
• Can work with other Modbus slaves
• Provide PM-3033/3133/3114/3112 profile examples and ESI file
• Supports maximum Baud Rate 115200 bps
• Allows system integrators to retro-fit older automation devices into modern EtherCAT communication structures
• Requires no hardware or software changes to be made to the connected device
• Compatible with all PLCs with EtherCAT support
• Performs complete serial protocol conversion, no PLC function blocks required
• RoHS compliant

Features
• EtherCAT slave
• Two channels, 32-bit incremental encoder counters
• Encoder counting mode: CW/CCW, Pulse/Direction, A/B Phase
• Maximum counting rate: 4 MHz
• Encoder Input: A, B, C differential or single-ended signals
• Two digital input for counter latching
• Two digital output for position compare signal trigger: single and auto-increment compare
• Encoder digital input filter
• Input level: 5V, 12V/24V with internal resistor
• Polarity setting by software for active high or active low encoder input
• A/B/C signal isolation voltage: 2500V optical isolation
• LED indicators for EtherCAT and encoder status
• EtherCAT:

  – 2 x RJ-45 bus interface

  – Distance between stations up to 100 m (100BASE-TX)

  – Support daisy chain connection

  – EtherCAT conformance test tool verified

  – Supports Free-Run, SM synchron and Distributed Clock (DC) operation modes.

Features
• No extra software tool is required! No more programming! Using browsers to perform system setting and logic rule edition
• 7″ TFT LCD(PMD-2206) / 10″ TFT LCD(PMD-4206) with Touch Panel for the operation at the local side & PoE (Power over Ethernet) supported
• Support at most “24 ICP DAS Modbus Power Meter modules + 8 Modbus I/O modules” (Max. total of 16 TCP type modules)
  – COM1 and COM2 interface can connect to Max. 16 Modbus RTU modules (include Power Meter & I/O Module) individually
  – LAN interface can connect to Max. 16 Modbus TCP modules (include Power Meter & I/O Module)
  – Support at most 4 ICP DAS PM-4324 series Power Meters
• Display real-time or historical power data by browser or local display
• Provide power data statistics report by browser
• Provide data log operation for power data & I/O channel data. Provide data file auto send-back & recovery when disconnected network is resumed
• Built-in IF-THEN-ELSE logic engine for power demand management
• Provide alarm message notification via LINE, Messenger, Email or WeChat
• Provide Schedule function for operations of devices
• Polarity setting by software for active high or active low encoder input
• Support Modbus TCP/RTU, SNMP, MQTT and FTP protocols for seamless integration with IoT/SCADA/IT system
• Support connection with IoT Cloud Platform (Microsoft Azure and IBM Bluemix); and ICP DAS IoTstar Cloud software

M-Bus (Meter-Bus) is a communication interface widely used for remote reading of meters such as: electricity meters, water meters, heat meters, etc. It is easy to install for its two-wire system already includes power and communication function. It also features the most important feature: robustness. M-Bus has its own physical layer and protocol. Therefore, it is usually required to be switched to other systems, such as Modbus, to facilitate the overall application. Modbus RTU is one of the most common communication standards in automation. ICP DAS developed the gateway GW-7828 for Modbus RTU to M-Bus, allows the direct transmission of meter data to a control system using Modbus RTU. The GW-7828 supports operating up to 100 meters on the M-Bus. The GW-7828 serves as a Modbus RTU slave gateway via RS-232, RS-422 or RS-485. After an initial configuration by M-Bus utility, GW-7828 will read out the meter data automatically. The PLC or PC as a Modbus RTU master can access meter data via a serial connection easily.

Features
• Supports M-Bus standard: EN-13757, CJ/T-188
• Supports up to 100 M-Bus slaves
• Supports Modbus RTU function code 0x03 and 0x04
• Serial Baud and M-Bus Baud can be configured separately
• Provides 10 kinds of Baud for default, 6 kinds of Baud for user-defined
• Allows updating firmware by the RS-232 port
• M-Bus overloading alarm
• Overcurrent and short-circuit protection on the M-Bus port
• 3750 Vrms photo-couple isolation on the M-Bus port
• ±4 kV ESD to contact
• Reverse polarity protection on power
• Watchdog inside
• Provide 3 LED indicators, PWR LED, MTX LED and MRX LED